Champions League

List of contents of this article:

• 1,Champions League fanuc system speed programming parameters
• 2, How to set the pitch parameters of FANUC system?
• 3, fanuc system oiling parameters
• 4, How to change the parameter settings of fanuc CNC system?

fanuc system speed programming parameters

The speed limit parameters of Fanuc G1 include the following four aspects. Maximum feed speed: refers to the maximum movement speed of the workpiece in the direction of the machining axis during the machining process, generally meters/minute or inch/minute. Maximum rotation speed: refers to the maximum rotational speed of the spindle, generally rotation/minute.

Adjust the driver settings: Enter the corresponding driver settings interface according to the driver system of the robot. Modify the speed value: In the speed setting option, find the currently set speed value (2000) and modify it to the target speed value (3000).

Walking the arc in the G2/G3 formatJust give the F value again, and the whole program speed can also be adjusted with the machine tool. F is the modal. After the first time the value is given, if F does not appear again, it will always be the original speed, and when milling the arc, the speed will indeed slow down, or remove G1Q1 to try.

Hello! Try the parameter number 1420 x axis z axis y axis. If it is fast, increase it, and decrease it if it is small. The unit is how many millimeters per minute? If it is helpful to you, please adopt it.

How to set the pitch parameters of FANUC system?

and 2085, change the reference counter capacity to 1821. The screw materials commonly used in China include No. 45 steel, 40Cr, ammonia steel, 38CrMOAl, high-temperature alloy, etc. 1) No. 45 steel is cheap and has good processing performance, but has poor wear resistance and corrosion resistance. Heat treatment: modulation HB220-270, high-frequency quenching HRC45--48.

The screw is a 12mm Fanaco system. The parameter setting method is as follows: put NC in MDI mode or emergency stop state; press the setting function key once or more times;AFTER ENTERING THE SETTING INTERFACE, MOVE THE CUSER TO PARAMETERWRITE; DISPLAY THE INTERFACE CONTAINING THE SETTING PARAMETERS, AND ENTER THE DATA BY PRESSING THE CONFIRMATION SOFT KEY TO COMPLETE.

r: Chamfer amount. When the pitch is represented by L, it can be set from 0.0L to 9L, and the unit is 0.1L (two-digit: from 00 to 99). This value is modal. This value can be set by parameter 5130, which can be changed by the program instruction. A: The angle of the tip of the knife.

First, turn on the parameter switch, then select the input method, enter the program page, enter the parameter value to be modified, and then press the [Insert] or [Enter] key to complete the modification.

Method 1: Modify parameters: 0#2=1 (0 is metric) Method 2: InSETTING screen (the screen that changes the I/O channel), there is an option that can also be modified directly.

If there is no transmission ratio, 2084 is set to 1 2085 is set to 100 Baidu Shared House There is a lot of knowledge about numerical control in this blog, which can improve the technology.

fanuc system oiling parameters

Fanaco md oiling time parameters: the first one is set to 1200000, that is, 1200 seconds = 20 minutes of oiling, and then the second is set to 15,000, That is, it stops after 15 seconds of oiling. The specific interval time and oiling time are adjusted according to the needs of the machine tool.

First of all, the K parameter, KOTo change 1, change K1 to 0 and then change the T parameter, T4 is the length of the oiling time, generally changed to 30 seconds, T6 is the oiling interval, generally 10 minutes.

Please refer to the T parameter TOO12 set 0 TOO14 interval TOO16 oiling time, and also controlled by ordinary parameters.

How to change the parameter settings of fanuc CNC system?

1. Parameter modification: select the MDI mode first, and change the parameter switch to 1. THE SYSTEM PARAMETERS ARE IN THE SYSTEM BUTTON, AND THE K PARAMETERS ARE IN THE SYSTEM - "PMCMNT - "K PARAMETER".

2. Department of DevelopmentUnified FANUC parameter modification: select the "MDI" mode first, and change the parameter switch to "1" in the "OFFSET" button. THE SYSTEM PARAMETERS ARE IN THE "SYSTEM" BUTTON, AND THE K PARAMETER IS IN THE "SYSTEM" -- "PMCMNT" - "K PARAMETER".

3. Enter the zero return mode: On the CNC lathe of the Fanuc system, you usually need to press the RESET button and select the zero return mode to enter the zero return mode. For specific operation methods, please refer to the operation manual of the machine tool. Set the zero return method: according to the actual situation, choose the zero return method.